Voltage Divider Calculator

Same unit as the resistors. A load pulls the output down.

Output voltage
—
For design guidance only. Real resistors have tolerance, and the output also shifts with temperature and with whatever is connected to it. Check power ratings before building. The load option applies only when finding Vout.

A voltage divider calculator helps you determine the output voltage of a circuit using the input voltage and resistor values. It is commonly used in electronics to reduce a voltage to a lower level for sensors, microcontrollers, measurement circuits, and other components.

A basic voltage divider uses two resistors connected in series. The output voltage depends on the ratio between the resistors. By changing their resistance values, you can control how much of the input voltage appears at the output.

The standard voltage divider formula is:

Vout = Vin × R2 / (R1 + R2)

Where:

  • Vout: Output voltage
  • Vin: Input or source voltage
  • R1: Resistor connected between the input and output
  • R2: Resistor connected between the output and ground

This guide explains how to calculate voltage dividers with two, three, four, or five resistors, understand the formula, and use voltage dividers in practical electronic circuits.

You can also use this AEC Calculator.

What Is a Voltage Divider?

A voltage divider is a circuit that produces a lower voltage from a higher input voltage. It usually consists of two or more resistors connected in series across a voltage source.

The output is taken from a point between the resistors and a reference point, usually ground.

<Add a simple two-resistor voltage divider circuit diagram here.>

In a basic circuit, R1 and R2 are connected in series. The same current flows through both resistors when the output is unloaded. The input voltage is divided according to their resistance values.

For example, if you connect two equal resistors across a 10V source, the output voltage across either resistor is 5V.

Voltage dividers are useful for creating reference voltages, reading resistive sensors, and reducing signal levels. However, they are not suitable for every voltage-conversion task because the output can change when a load is connected.

Voltage Divider Formula

The standard voltage divider equation for two resistors is:

[
V_{out}=V_{in}\times\frac{R_2}{R_1+R_2}
]

Where:

  • (V_{out}) is the voltage measured across R2.
  • (V_{in}) is the total source voltage.
  • (R_1) is the upper resistor.
  • (R_2) is the lower resistor connected to ground.

The fraction represents the proportion of the input voltage that appears across R2.

Example: Two-Resistor Voltage Divider

Suppose you have:

  • Input voltage = 12V
  • R1 = 4kΩ
  • R2 = 8kΩ

Using the formula:

[
V_{out}=12\times\frac{8}{4+8}
]

[
V_{out}=12\times\frac{8}{12}
]

[
\boxed{V_{out}=8V}
]

The output voltage is 8V.

The remaining 4V is dropped across R1.

How to Calculate Voltage Divider Output

Follow these steps:

  1. Identify the input voltage supplied to the circuit.
  2. Find the resistance values of R1 and R2.
  3. Make sure R1 is the resistor above the output point and R2 is below it.
  4. Add the two resistance values.
  5. Divide R2 by the total resistance.
  6. Multiply the result by the input voltage.

The result is the ideal output voltage across R2 when no significant load is connected.

Voltage Divider Calculator With 2 Resistors

A two-resistor voltage divider is the simplest and most common arrangement. It is used when you need to reduce an input voltage to a specific level.

For example, suppose you have a 5V input and want to produce approximately 3.3V.

Choose:

  • R1 = 1kΩ
  • R2 = 2kΩ
  • Vin = 5V

Calculation:

[
V_{out}=5\times\frac{2000}{1000+2000}
]

[
V_{out}=5\times0.6667
]

[
\boxed{V_{out}\approx3.33V}
]

The circuit produces approximately 3.33V under ideal unloaded conditions.

This arrangement can be useful for reducing a signal voltage, provided the connected device accepts the resulting voltage and the load does not significantly affect the divider.

Voltage Divider Calculator With 3 Resistors

A voltage divider with three resistors uses three resistors connected in series. You can take the output from different points along the resistor chain.

For an output measured across the bottom resistor R3:

[
V_{out}=V_{in}\times\frac{R_3}{R_1+R_2+R_3}
]

For example:

  • Vin = 12V
  • R1 = 1kΩ
  • R2 = 2kΩ
  • R3 = 3kΩ

Calculation:

[
V_{out}=12\times\frac{3}{1+2+3}
]

[
V_{out}=12\times\frac{3}{6}
]

[
\boxed{V_{out}=6V}
]

If you measure the voltage across R2 and R3 together, the result is:

[
V_{out}=12\times\frac{2+3}{1+2+3}
]

[
\boxed{V_{out}=10V}
]

The output voltage depends on where you connect the measurement point.

Voltage Divider Calculator With 4 Resistors

A four-resistor divider provides additional voltage levels along the resistor chain.

For four resistors connected in series, the voltage across the bottom resistor R4 is:

[
V_{out}=V_{in}\times\frac{R_4}{R_1+R_2+R_3+R_4}
]

Example:

  • Input voltage = 20V
  • R1 = 1kΩ
  • R2 = 2kΩ
  • R3 = 3kΩ
  • R4 = 4kΩ

Calculation:

[
V_{out}=20\times\frac{4}{1+2+3+4}
]

[
V_{out}=20\times\frac{4}{10}
]

[
\boxed{V_{out}=8V}
]

If you take the output across R3 and R4 together, the output becomes:

[
V_{out}=20\times\frac{3+4}{10}
]

[
\boxed{V_{out}=14V}
]

This arrangement can create multiple reference voltage levels for measurement or electronic control circuits.

Voltage Divider Calculator With 5 Resistors

A five-resistor voltage divider works on the same principle. The total resistance is the sum of all five resistors.

When the output is measured across R5:

[
V_{out}=V_{in}\times\frac{R_5}{R_1+R_2+R_3+R_4+R_5}
]

Example:

  • Vin = 15V
  • R1 = 1kΩ
  • R2 = 1kΩ
  • R3 = 2kΩ
  • R4 = 2kΩ
  • R5 = 4kΩ

Total resistance:

[
R_T=1+1+2+2+4=10k\Omega
]

Output voltage:

[
V_{out}=15\times\frac{4}{10}
]

[
\boxed{V_{out}=6V}
]

For an output taken from another point, add the resistance values between that point and ground. Divide that sum by the total series resistance, then multiply by the input voltage.

General Voltage Divider Formula for Multiple Resistors

The same formula works for any number of resistors connected in series.

If the output is measured across a group of lower resistors, use:

[
V_{out}=V_{in}\times\frac{R_{\text{below}}}{R_{\text{total}}}
]

Where:

  • (R_{\text{below}}) is the combined resistance between the output point and ground.
  • (R_{\text{total}}) is the sum of all series resistances.

For example, if a circuit contains five resistors and the output is measured across R3, R4, and R5:

[
V_{out}=V_{in}\times\frac{R_3+R_4+R_5}{R_1+R_2+R_3+R_4+R_5}
]

This method makes it possible to calculate voltage at different points in a resistor ladder without using a separate formula for every circuit.

Voltage Divider and Ohm’s Law

Ohm’s law explains the relationship between voltage, current, and resistance:

[
V=I\times R
]

Where:

  • V = Voltage in volts
  • I = Current in amperes
  • R = Resistance in ohms

In a basic unloaded voltage divider, R1 and R2 are connected in series. The total resistance is:

[
R_T=R_1+R_2
]

The current flowing through the circuit is:

[
I=\frac{V_{in}}{R_1+R_2}
]

The output voltage across R2 is:

[
V_{out}=I\times R_2
]

Substituting the current formula gives:

[
V_{out}=\frac{V_{in}}{R_1+R_2}\times R_2
]

Therefore:

[
\boxed{V_{out}=V_{in}\times\frac{R_2}{R_1+R_2}}
]

This shows how the voltage divider formula comes directly from Ohm’s law.

Voltage Divider With a Load Resistor

The basic voltage divider formula assumes that no significant load is connected to the output. In a real circuit, a device connected across R2 draws current and can change the output voltage.

When a load resistor (R_L) is connected across R2, calculate the parallel resistance first:

[
R_{parallel}=\frac{R_2\times R_L}{R_2+R_L}
]

Then calculate the loaded output:

[
V_{out}=V_{in}\times\frac{R_{parallel}}{R_1+R_{parallel}}
]

Loaded Voltage Divider Example

Suppose:

  • Vin = 12V
  • R1 = 1kΩ
  • R2 = 2kΩ
  • Load resistance = 2kΩ

First, calculate the parallel resistance:

[
R_{parallel}=\frac{2000\times2000}{2000+2000}
]

[
R_{parallel}=1000\Omega
]

Now calculate the output:

[
V_{out}=12\times\frac{1000}{1000+1000}
]

[
\boxed{V_{out}=6V}
]

Without the load, the output would be 8V. Connecting the 2kΩ load reduces it to 6V.

This is why load resistance should be considered when designing a practical voltage divider.

AC Voltage Divider Calculator

An AC voltage divider uses the same basic principle as a DC divider, but the calculation depends on the electrical properties of the components.

For a simple circuit containing two pure resistors in series, the voltage divider ratio also applies to AC voltage:

[
V_{out}=V_{in}\times\frac{R_2}{R_1+R_2}
]

The same ratio applies to the AC voltage’s RMS value, assuming the circuit is resistive and the output is unloaded.

However, if the circuit contains capacitors, inductors, or other frequency-dependent components, you must use impedance instead of resistance.

The general AC voltage divider formula is:

[
V_{out}=V_{in}\times\frac{Z_2}{Z_1+Z_2}
]

Where:

  • (Z_1) = Impedance of the first component or network
  • (Z_2) = Impedance of the output component or network
  • (V_{in}) = Input voltage
  • (V_{out}) = Output voltage

Impedance includes both resistance and reactance. Its value can change with frequency, so an AC divider containing capacitors or inductors may produce different output voltages at different frequencies.

Applications of Voltage Dividers

Voltage dividers are used in many electronic circuits because they provide a simple way to obtain a lower voltage or create a measurable signal.

1. Potentiometers

A potentiometer is a variable resistor that can operate as an adjustable voltage divider.

It usually has three terminals:

  • One outer terminal connects to the input voltage.
  • The other outer terminal connects to ground.
  • The middle terminal connects to the adjustable output.

Moving the wiper changes the resistance on either side of the output connection. This changes the output voltage.

Potentiometers are commonly used in volume controls, adjustable settings, calibration circuits, and electronic controls.

2. Level Shifters

A voltage divider can reduce a signal voltage before it reaches a device that accepts a lower input voltage.

For example, a 5V signal may need to be reduced before connecting to a 3.3V microcontroller input.

Using:

  • Vin = 5V
  • R1 = 1kΩ
  • R2 = 2kΩ

The output is:

[
V_{out}=5\times\frac{2}{1+2}
]

[
\boxed{V_{out}=3.33V}
]

This can work for a suitable high-impedance input, but a resistor divider is not a universal logic-level converter. Check the device’s maximum input voltage, input current, signal speed, and electrical requirements before connecting it.

3. Resistive Sensor Reading

Many sensors change their resistance according to an environmental condition. A voltage divider can convert this resistance change into a voltage that a microcontroller or measurement circuit can read.

Common examples include:

  • Thermistors
  • Light-dependent resistors (LDRs)
  • Force-sensitive resistors
  • Some pressure sensors

A microcontroller’s analog-to-digital converter can measure the resulting voltage and use it to estimate the sensor’s value.

4. Thermistor Circuits

A thermistor changes resistance as temperature changes. Connecting it with a fixed resistor creates a voltage divider whose output changes with temperature.

Suppose:

  • Vin = 5V
  • Fixed resistor = 350Ω
  • Thermistor resistance = 350Ω

If the thermistor is connected as the lower resistor:

[
V_{out}=5\times\frac{350}{350+350}
]

[
\boxed{V_{out}=2.5V}
]

If its resistance changes to 500Ω:

[
V_{out}=5\times\frac{500}{350+500}
]

[
\boxed{V_{out}\approx2.94V}
]

The output voltage changes as the thermistor resistance changes. A microcontroller can measure this voltage and use a suitable calibration equation or lookup table to estimate temperature.

5. Reference Voltage Circuits

A resistor divider can create a reference voltage for some electronic circuits. It can be useful in low-current applications where a stable, lightly loaded voltage is needed.

For more demanding applications, a voltage reference IC or regulator is often a better choice because resistor-divider output voltage can vary with supply voltage, resistor tolerance, temperature, and load current.

Common Voltage Divider Resistor Combinations

The following resistor combinations provide approximate output voltages for selected input levels. R1 is connected to the input, and R2 is connected to ground.

Input voltageR1R2Approximate output
12V6.8kΩ5.1kΩ5.05V
9V6.8kΩ8.2kΩ4.91V
12V18kΩ6.8kΩ3.27V
9V12kΩ6.8kΩ3.27V
5V1kΩ2kΩ3.33V

These are ideal calculated values. Actual output voltage may vary because of resistor tolerance, source voltage variation, and the connected load.

How to Choose Resistor Values for a Voltage Divider

Choosing the correct resistor values involves more than matching the desired output voltage. You should also consider current consumption, power dissipation, load resistance, and resistor availability.

1. Calculate the Required Resistance Ratio

Rearrange the voltage divider formula:

[
\frac{R_2}{R_1+R_2}=\frac{V_{out}}{V_{in}}
]

This gives the resistance ratio needed to produce the desired output.

2. Select Practical Resistor Values

Choose standard resistor values that provide the required ratio. Common resistor values are available in standard E-series ranges.

3. Calculate Divider Current

The current through an unloaded divider is:

[
I=\frac{V_{in}}{R_1+R_2}
]

A lower total resistance draws more current. A higher total resistance reduces current consumption but makes the output more sensitive to loading and leakage.

4. Check Resistor Power

The power dissipated by each resistor can be calculated using:

[
P=I^2R
]

Check that the selected resistor’s power rating is higher than its expected dissipation, with a suitable safety margin.

5. Consider Resistor Tolerance

Real resistors have manufacturing tolerances. A 1% resistor may have a different actual resistance from its marked nominal value.

This variation can cause the output voltage to differ from the calculated result. Use tighter-tolerance resistors when the application requires better accuracy.

Voltage Divider vs. Parallel Resistor Calculator

A voltage divider calculator and a parallel resistor calculator perform different calculations.

FeatureVoltage divider calculatorParallel resistor calculator
Main purposeCalculates output voltageCalculates equivalent resistance
Circuit arrangementUsually series resistorsResistors connected across common nodes
Main formula(V_{out}=V_{in}\times R_2/(R_1+R_2))(1/R_T=1/R_1+1/R_2+\cdots)
Typical applicationReducing or measuring voltageFinding total parallel resistance

For two resistors connected in parallel, the equivalent resistance is:

[
R_T=\frac{R_1\times R_2}{R_1+R_2}
]

A parallel resistor calculation may be needed when finding the effective resistance of a loaded voltage divider.

Voltage Divider Calculator App, APK, and Download Options

You can use an online voltage divider calculator through a web browser without installing additional software. This is useful when you need to check resistor values quickly or calculate output voltage while designing a circuit.

If you prefer an application, look for an electronics calculator app that includes:

  • Two-resistor voltage divider calculations
  • Multiple-resistor series calculations
  • Resistor color code identification
  • Ohm’s law calculations
  • Parallel and series resistance calculations
  • Unit conversion between ohms, kilo-ohms, and mega-ohms

For Android, check the Google Play Store for a reputable electronics calculator app. If you need a voltage divider calculator APK, use a trusted source and verify the developer and app permissions before installing it.

For PC users, a browser-based calculator is often sufficient. You can also use an electronics design or circuit simulation program to test more complex circuits.

A downloaded app should not be necessary for basic voltage divider calculations.

Frequently Asked Questions

What is the voltage divider formula?

The standard formula for a two-resistor voltage divider is:

[
V_{out}=V_{in}\times\frac{R_2}{R_1+R_2}
]

It calculates the output voltage across R2 when the output is unloaded.

How do I calculate a voltage divider with two resistors?

Add R1 and R2, divide R2 by their total resistance, and multiply the result by the input voltage. The result is the voltage across R2.

Can I use a voltage divider with three or more resistors?

Yes. Add all series resistor values to find the total resistance. Then divide the combined resistance below the output point by the total resistance and multiply by the input voltage.

How do I calculate a voltage divider with five resistors?

For five series resistors, if the output is measured across R5:

[
V_{out}=V_{in}\times\frac{R_5}{R_1+R_2+R_3+R_4+R_5}
]

If the output is taken across multiple lower resistors, add those resistance values in the numerator.

Does a voltage divider reduce current?

A voltage divider draws current from the source. Its current depends on the input voltage and total series resistance. Connecting a load also changes the current distribution and may reduce the output voltage.

Can a voltage divider increase voltage?

No. A passive resistor voltage divider cannot produce an output voltage greater than its input voltage. It is designed to reduce voltage.

Can I use a voltage divider for AC?

Yes, a divider made from two resistors can divide an AC voltage using the same resistance ratio. Circuits containing capacitors or inductors require impedance-based calculations because their behavior depends on frequency.

What is the difference between a voltage divider and a voltage regulator?

A voltage divider uses resistors to produce a lower voltage, but its output can change with the load and input voltage. A voltage regulator is designed to maintain a more stable output over a specified range of input and load conditions.

How do I calculate the output voltage when a load is connected?

First calculate the parallel equivalent resistance of R2 and the load resistor. Then use that equivalent resistance in the voltage divider formula:

[
V_{out}=V_{in}\times\frac{R_2\parallel R_L}{R_1+(R_2\parallel R_L)}
]

What resistor values should I use for a 5V to 3.3V voltage divider?

One possible combination is R1 = 1kΩ and R2 = 2kΩ. With a 5V input, the ideal unloaded output is approximately 3.33V. Confirm that the load and signal requirements are suitable.

Does resistor tolerance affect output voltage?

Yes. Actual resistor values may differ slightly from their nominal values. This changes the resistance ratio and can cause the output voltage to vary. Use precision resistors when better accuracy is required.

Conclusion

A voltage divider calculator makes it easy to determine the output voltage of a resistor circuit. Whether you are working with two resistors or building a divider with three, four, or five resistors, the calculation follows the same basic principle: the output voltage depends on the resistance below the output point compared with the total series resistance.

Voltage dividers are useful in potentiometers, sensor circuits, signal-level reduction, and electronic measurement systems. However, always consider load resistance, resistor tolerance, current consumption, and power dissipation when applying the calculation to a real circuit.